![]() This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. Our customer service support will work hard to put a smile back in your face. Please contact us if you have any concerns about the product, prior to leaving any online feedback, so that we may address your concern as quickly as possible. Please text: Hi eMacros, I like it, my order number is *** to our email: or contact us via Facebook page: you will enjoy our VIP treatment. We guarantee your complete satisfaction for this purchase.Search for fo find our page and get a rapid response service.If you have any problems, please contact us by navigating to: then click Contact Us, we will assist you as soon as possible. Thank you for choosing eMacros, we provide lifetime warranty and technical support for our customers. Check the sensor switch settings (Refer to Instruction Manual – Assembly & Setup). The PIR Motion Sensor operates, but the base station does not respond.The sensors will not work properly outside of this temperature range. Note: The sensors operate best in the -4F to 140F degree range. The PIR sensor detects the movements with heat sources please adjust the sensor eye with horizontal angle to the engine of the car. Vehicle Alert Installation: The best mounting position for detecting vehicles is about 4 feet (1.2ml high.Position the sensor to avoid direct sunlight shining on the sensor eye while simultaneously keeping the solar cell facing upward. The sensor should be able to swivel as needed. Mount the waterproof PIR Motion Sensor vertically on a solid surface 3-5 feet (1-l.5m) above the ground (rotate sensor to access screw holes).The Base Station will produce a unique tone based upon the sensor’s setting. Test the PIR Motion Sensor by waving your hand in front of the sensor.Note: Each Separate channel uses an unique chime, allowing you to match different chimes with different channels. When detecting movements, a sensor eye will flash red only when assigned to lines 1 and 2, not lines 3 or 4. CH 1-4 Switch: Select a different channel for each outside sensor.Set the detection range to High (30feet), Low (20 feet), or turn sensor Off. High/ Low/ Off Switch: First, open the black silicone seal cap at the bottom of the PIR Motion Sensor, then turn on the sensor by switching to High or Low.If the blue light wont illuminate, the battery may be fully charged, you can install it directly. Note: The sensor hos been tested several times in the factory. The blue light will turn off once the battery is fully charged. The blue light will illuminate while charging. Before installing the PIR Sensor, recharge the sensor (with 18650 battery attached) using the AC adapter to ensure a full charge.Powering off the base station will reset the volume to the factory setting. Volume adjustments will be heard on subsequent alarm activations, not while adjustments are being made. Adjust the Base Station volume as needed, using the adjustable Volume+/- buttons.To turn the Base Station on /off, hold down the power button until you hear the on/off tone. The red power light will illuminate on #3 when the Base Station is on.Base Station can also run on (4)AA batteries for up to 2 weeks, as backup in case of power outage. Plug the Base Station into an outlet using the AC adapter.You may purchase a standalone Allstate Plan by going to and searching for an Allstate Plan.ĢRequires integration with Key by Amazon. The cost for the Allstate Protection Plan is included in the cost of the Ring Protect Plan. In the U.S., in lieu of the Ring extended warranty, Eligible Ring Devices are covered via a service contract administered by SquareTrade, an Allstate company SquareTrade/Allstate terms are available here. Non-Ring and other third-party devices are not eligible for the extended warranty. ![]() Snapshot Capture photos in the cloud are stored up to 7 days.įor extended warranty coverage, "Eligible Ring Devices" are Ring devices covered by an active Protect Plus/Pro Plan, if the Ring device was under the 1-year manufacturer’s warranty period at the time you added the device to your Protect Plus/Pro Plan. Changing your video storage time will only affect videos that are recorded after you adjust your storage time setting. Your Ring videos in the cloud are stored temporarily, up to 180 days. Terms and conditions apply.įree trial is not applicable for locations with an existing Ring Protect Plus or Protect Pro subscription. See Ring Protect Subscription Plans for more information. 1Find details on Ring Protect Plans below.
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |